diff --git a/Hardware/bananapi-f3.md b/Hardware/bananapi-f3.md
new file mode 100644
index 0000000000..dbc2717e23
--- /dev/null
+++ b/Hardware/bananapi-f3.md
@@ -0,0 +1,98 @@
+---
+riscv_hardware: true
+cmake_plat: bananapi-f3
+xcompiler_arg: -DRISCV64=1
+platform: Banana Pi BPI-F3
+arch: RV64GCVB
+virtualization: false
+iommu: false
+simulation_target: false
+verification: []
+Contrib: "Community"
+Maintained: "10xEngineers"
+soc: SpacemiT K1
+cpu: X60
+parent: /Hardware/
+SPDX-License-Identifier: CC-BY-SA-4.0
+SPDX-FileCopyrightText: 2025 10xEngineers
+---
+
+# Banana Pi BPI-F3
+
+The Banana Pi BPI-F3 is an industrial-grade RISC-V single-board computer
+from Banana Pi, based on SpacemiT K1 SoC. It has an octa-core RISC-V (8 × X60)
+CPU, with integrated 2.0 TOPs AI computing power.
+
+{% include hw-info.html %}
+
+Details and links to manuals can be found on the [Banana Pi product
+page](https://docs.banana-pi.org/en/BPI-F3/BananaPi_BPI-F3).
+
+The SoC technical reference manual can be found [on
+SpacemiT website](https://developer.spacemit.com/documentation?token=GAmMwCrRUiZAo5kXKUQcNNacnwb&type=pdf).
+
+The Banana Pi BPI-F3 arrives with the following boot process:
+
+1. Firmware starts
+2. OpenSBI starts
+3. U-Boot proper starts
+
+From U-Boot proper you can then load and start an seL4 image, see below for details.
+
+## Building the GCC toolchain
+
+{% include risc-v.md %}
+
+## Building seL4test
+
+{% include sel4test.md %}
+
+## Booting
+
+There are multiple ways to boot from U-Boot, documented below is booting via TFTP and from
+a microSD card.
+
+### Obtaining the DTB {#dtb}
+
+Since we are using a `uImage` for the Banana Pi BPI-F3, U-Boot requires a Device Tree Blob (DTB) alongside
+the binary image to boot.
+
+The Device Tree Source (DTS) can be compiled from the seL4 tree with the Device Tree Compiler (`dtc`):
+```sh
+dtc -I dts -O dtb sel4/tools/dts/bananapi-f3.dts > bananapi-f3.dtb
+```
+
+### Booting via microSD card
+
+These instructions expect the microSD card to be paritioned with FAT.
+
+The microSD card slot registers as device `0` in U-Boot so to see if the device
+is recognised run:
+
+```sh
+mmc dev 0
+# Check that the card info is expected
+mmc info
+# List partitions
+mmc part
+```
+
+To load and run the image:
+
+```sh
+fatload mmc 0:<PARTITION> 0x200000 sel4test-driver-image-riscv-bananapi-f3
+fatload mmc 0:<PARTITION> 0x31000000 bananapi-f3.dtb
+bootm 0x200000 - 0x31000000
+```
+
+### Booting via TFTP
+
+If you have setup a TFTP server, enter the following commands on the U-Boot console
+to load an image via the network.
+
+```sh
+dhcp
+tftpboot 0x200000 <YOUR_TFTP_SERVER_IP_ADDRESS>:sel4test-driver-image-riscv-bananapi-f3
+tftpboot 0x31000000 <YOUR_TFTP_SERVER_IP_ADDRESS>:bananapi-f3.dtb
+bootm 0x200000 - 0x31000000
+```